GO-10S13MG (0.08s/60°, 2.0kg.cm)

Kód
KAV20.10S13MG
Márka
KAVAN
Elérhetőség
Ár:
549 Kč
incl. VAT

High speed programmable digital pico servo 13g with titanium gear and input voltage range 4.8-6.0V, 2xBB, ideal for small model aircraft, 1:16-1:24 RC cars, 400-450 size helis etc. Torque 1.6kg.cm, speed 0.09s/60° at 4.8V, torque 2.0kg.cm, speed 0.08s/60° at 6.0V. Aluminium middle case heatsink for perfect cooling under high load.

High speed programmable digital pico servo with titanium gear and double BB-ed output shaft for small RC model planes, 1:16-1:24 RC cars, 400-450 size helicopters etc. Plastic case with middle aluminium heatsink for perfect cooling under high load. GO-10S13MG is programmable using the KAVAN GO servo USB programmer/interface and PC software. Programmable Functions ... több »

High speed programmable digital pico servo with titanium gear and double BB-ed output shaft for small RC model planes, 1:16-1:24 RC cars, 400-450 size helicopters etc. Plastic case with middle aluminium heatsink for perfect cooling under high load.

GO-10S13MG is programmable using the KAVAN GO servo USB programmer/interface and PC software.

Programmable Functions

  • Servo Angle: Maximal servo rotation angle range setting. The default range is ca 120° within the regular RC signal pulse width range (900~2100 µs); ca 180° within the max. signal pulse width range (500~2500 µs).
  • Servo Neutral: Servo neutral (centre) position setting.
  • Damping Factor: Servo damping setting – adjust the characteristics of the servo when stopping.
  • PWM Power: Adjusts the servo output power. The higher the power, the higher the speed and torque of the servo – indeed also the current consumption will be higher.
  • Sensitivity: Servo sensitivity (Dead Band) setting. The higher sensitivity the narrower the dead band – servo moves only if the change of the signal pulse width is bigger than the dead band width. Too high setting may cause servo jitter in some applications. Range: Ultra High (ca 1 µs dead band) – High (ca 2 µs) – Medium (ca 3 µs) – Low (ca 4 µs)
  • Soft Start: Turns on/off the soft start feature. If ON, the servo goes slowly to the initial position corresponding to the servo signal once the power is switched on.
  • Reverse: Reverses the servo movement direction.
  • Narrow Band: FUTABA SR Mode – only for use with FUTABA radio channels working in the SR mode. Do not turn the option on if you are using a different setting of your FUTABA radio or any other radio.
  • SANWA SSR: SANWA SSR Mode - only for use with SANWA radio channels working in the SSR mode. Do not turn the option on if you are using a different setting of your SANWA radio or any other radio.
  • Lost PPM Protection (Fail-Safe): In the case the control signal from the receiver is lost completely or cannot be decoded correctly (due to interference) the servo can use choose one of three fail-safe modes:
    • (a) Release: No fail-safe protection.
    • (b) Keep Position: Keeps the position corresponding to the last correct control signal.
    • (c) Go Neutral Position: The servo returns to the neutral (1500 µs pulse width) position.
  • Over Load protection: Enables or disables overload protection of the servo in three levels – once the overload conditions last for the pre-set time (in seconds), the output power of the servo is reduced to the corresponding pre-set level (% of the max. power).
  • Default: Restores the factory default setting of the connected servo.

Standard input voltage range 4.8-6.0 V (nominal).

25T/4.94 mm output shaft.

Servo dimensionsMicro
Servo typeDigital
ProgrammableYes
Thrust at 4.8V [kg/cm]1.6
Thrust at 6.0V [kg/cm]2
Speed at 4.8V [s/60st.]0.09
Speed at 6.0V [s/60st.]0.08
Servo gearsTitanium
Ball bearings
High-voltageNo
Power supply [V]4.8 - 6
Length [mm]22.8
Width [mm]12
Height [mm]29.4
Weight [g]15
Intended forAeroplanes,Helicopters,On-road cars,Off-road cars,Boats

Ke správnému fungování webových stránek a k analýzám návštěvnosti používáme soubory cookies. Používáním webu souhlasíte s jejich užitím. BERU NA VĚDOMÍ