FOXY G3 Brushless Motor C2212-1000
Brushless electric motor with rotating case for model aircraft: glider 800g, trainer 700g, acro 600g, 3D 450g, KV1000 rpm on V, power supply Lixx 2-4 cells, shaft 3.175 mm. FOXY motors are marked on the basis of the stator dimensions! The markings according to the motor size is C2830.
The FOXY G3 motors are brushless 14-pole rotary casing electric motors with excellent electrical properties, a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantee excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for ... több »
|  |  |
The FOXY G3 motors are brushless 14-pole rotary casing electric motors with excellent electrical properties, a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantee excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.
| Engine marking system: CxxYY / zzzz |
| C - brushless motor ("outrunner", "circular") |
| xx - stator diameter in mm |
| YY - stator length in mm |
| zzzz - revolutions per volt (rpm / V), "KV" |
The FOXY G3 C2212-1000 is a small brushless motor designed to drive small models up to 800 g in flight, powered by a 2-cell or 3-cell Li-po battery. Perfect for Dumas Park Flyers and 1000-1200mm SIG / HERR models.
Engine Mounting: The FOXY G3 C2212-1000 is designed for both front and rear mounting. For front mounting at the front of the motor, use at least two (opposite) or four M3 bolts that extend into the front of the motor within 3 - 4 mm. The pairs of mounting screw holes in the motor front are regularly spaced 180 ° on 16 and 19 mm diameter circles. The engine bulkhead should be made of 2-2.5 mm aviation plywood. The rear mounting kit (mounting cross, tail propeller) is supplied with the engine.
Engine set includes: FOXY G3 C2212-1000 Brushless Motor with 3.5mm Gold-Plated Connectors, Rear Mounting Kit, Instruction manual.
Supply voltage LiXX cells: 2 - 3 ; RPM/V [RPM/min/V]: 1000 ; Max. power (30 s/3S LiPo) [W]: 160 ; No load current (2S) [mA]: 900 ; Max. peak current (30 s) [A]: 19 ; Diameter [mm]: 27.8 ; Length [mm]: 32 ; Shaft diameter [mm]: 3.175 ; Weight [g]: 62 ; Nr. of poles: 14 ; Timming [°]: 15 - 25 ; ESC [A] : 20 - 25 ; Sailplane up to Weight [g]: 800 ; Trainer up to Weight [g]: 700 ; Acrobat up to Weight [g]: 600 ; 3d up to Weight [g]: 400
The marking according to the engine dimensions: C2830; The marking according to the stator dimensions: C2212| Powering LiXX cells | 2 - 3 |
| RPM/V [ot./min/V] | 1000 |
| Max. power (30 s/3S LiPo) [W] | 160 |
| Open-circuit current (2S) [mA] | 900 |
| Max. peak current (30 s) [A] | 19 |
| Diameter [mm] | 27.8 |
| Length [mm] | 32 |
| Shaft diameter [mm] | 3.175 |
| Weight [g] | 62 |
| Poles count | 14 |
| Timing [°] | 15 - 25 |
| ESC [A] | 20 - 25 |
| Weight of glider (up-to) [g] | 800 |
| Weight of trainer (up-to) [g] | 700 |
| Weight of acrobat (up-to) [g] | 600 |
| Weight of 3D (up-to) [g] | 400 |
| 3S: 10x4,7” |